==================================================================
NOTES ON                                                April 1998 
   D-Link DFE-660 Fast Ethernet PC Card Diagnostic Program
==================================================================
    (c) 1998 Copyright D-Link Corporation  ALL RIGHTS RESERVED

   The Diagnostic Program permits you to verify the configuration
   and suspect the isolation of faults; Make sure to isolate your
   network before running the Diagnostic Program.

   The additional information describe as below:

   1. Files List
   --------------
        A list of diagnostic program files:

        DIAG.EXE    : The diagnostic program
        BASDIAG.EXE : The basic diagnostic program
        NETDIAG.EXE : The network diagnostic program
        DFE660.COM  : The ODI driver
        IPXODI.COM  : The IPX protocol driver for the ODI stack
        LSL.COM     : The link support layer for the ODI stack
        NET.CFG     : The ODI configuration file
        README.TXT  : This file

    2   Menu for Diagnostic Program
    --------------------------------
        The diagnostic main menu provides two options:

         i: Adapter Basic Diagnostics
            This option performs a diagnostic test on the adapter
            components.

        ii: Network Diagnostics
            This option allows you to test the connectivity of the adapter
            on the network.

        Diagnostic Program also lets you view the current adapter configuration,
        including:

        Viewed items: Your Current Configuration
                    <1> CS Vender
                    <2> CS Revision
                    <3> Node ID
                    <4> I/O Base Address
                    <5> Interrupt Number

        The following displays the DIAG main menu:

                         Main Menu ͻ
                          Adapter Basic Diagnostics 
                          Network Diagnostics       
                        ͼ


        The Adapter Basic Diagnostics option checks the major components
        on the adapter and network cable to ensure proper operation.
        The following is the screen print of the diagnostics screen.

          Adapter Diagnostic ͻ
           Node ID          : 00 80 C8 00 00 02                  
           I/O Base Address : E000                               
           Interrupt Number : 11                                 
                                Cycle   0                        
           SROM .......................................  PASS    
           CIS ROM ....................................  FAIL    
           Loopback Mode Testing ......................  Testing 
         ͼ

        Select Network Diagnostics to perform a live transmission test for
        checking the adapter's network connectivity. This test requires that
        LSL.COM, DFE660.COM and IPXODI.COM be located on the same directory
        as the Setup program.

                     Network Diagnostic ͻ
                     Set up as a master station 
                     Set up as a slave station  
                    ͼ

          The Network Diagnostics option tests the ability of the adapter
          to communicate with other stations on the network. This test
          requires one master station and one slave station. The master
          station is responsible for sending test packets to the network.
          The slave station is responsible for sending back these packets
          to the master station. There is good connectivity if all the
          packets sent by the master were able to come back.

          Before running this test, ensure to copy first LSL.COM,
          IPXODI.COM, DFE660.COM and NET.CFG to the same directory where
          the dagnostic program resides. Also, ensure that the slave and
          master stations use the same frame type specified in the net.cfg
          file. We provide everything you need in the \DIAG directory.
          To set up a station as master, select "Set up as a master
          station". To set up the other station as slave, select "Set up
          as a slave station".

          When you start the test, these messages appear on each station:

                              MASTER STATION

                       Master Station ͻ
                       Waiting Sending Receiving  
                          \       |        /      
                      ͼ

                               SLAVE STATION

     Slave Station ͻ
     Node Address     : 00 80 C8 00 00 02                               
     I/O Base Address : E000                 Test started at : 20:06:10 
     Interrupt Number : 11                   Current time    : 20:10:50 
                                                                        
                                                                        
     Transmit Packet Length .................................  1234     
     Transmit Packet Counter ................................  1111     
     Transmit Time Out Counter ..............................  0        
                                                                        
     Received Packet Length .................................  1234     
     Received Packet Counter ................................  1111     
     Received Error Counter .................................  0        
     No Response Counter ....................................  0        
     Data Mismatch Counter ..................................  0        
                                                                        
    ͼ

