All right, if you're ready, here's
an opportunity for you to get some hands-on practice using
the virtual lab.
[MUSIC PLAYING]
And here's our topology once again, with all eight routers.
Now, I do have a document on the management computer
you can use to copy and paste.
But here's what I would recommend you do.
These routers, not one of them is
going to be running a dynamic routing protocol to start.
In the previous video, we took a look
at an example of the commands we can use to implement it.
And what I'm going to have you do WEBVTT X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000
And what I'm going to have you do
is maybe take the text document as a guide and configure R1--
maybe go down the left hand side here--
R3, which is in two different areas, and R5.
Do at least two or three routers manually
so you can get the hang of it.
And then if you want to go ahead and copy/paste the rest
after you're comfortable with the commands--
because they are slightly different than what
we might be used to.
Once you are comfortable with it, you can copy/paste the rest
or do all of them.
Now, also, at the tail end of this hands-on lab,
I would ask you to not close the lab quite yet. WEBVTT X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000
I would ask you to not close the lab quite yet.
Because in the next video, I'd like to walk you through--
with your lab with the full configuration in place--
a few of my what used to be favorite commands that are now
adjusted so that they work if we're
running OSPF v3 officially.
We can still get the output we need.
Or things like interfaces and the link state database.
Just, you know, the simple things
that we might want to see.
So just to make sure we're on the same sheet of music,
I'm going to bring up the lab.
I just clicked on the link for the virtual lab
a few moments ago. WEBVTT X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000
a few moments ago.
And here it is.
So I've got tabs for R1 through R8.
Also, I've got PC1, PC7, and PC8,
as shown in the diagram right here,
hanging off their respective networks.
So this PC1's over here.
And this is PC7.
And this is PC8 over here.
If you want to use those as target points
for either IPv4 or IPv6, because once it's all working,
you're going to have OSPF support, courtesy
of OSPF version 3, with address families supporting
both of them.
WEBVTT X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000
I just realized I bumped something out of whack.
Let me fix that real quick.
And I bumped-- and it was this whole topology.
It's like, what happened there?
Oh, maybe I can do a-- hold on.
I'll do a Control Z to bring it back.
There we go.
I was like, hey, I've got a problem.
Everything's off a little bit.
All right.
So let me bring up the lab and just make sure we're
on the same sheet of music.
And here we go.
So there is the lab environment with the PCs.
Fantastic. WEBVTT X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000
Fantastic.
So here's R1.
I'm also going to go ahead and grab
the Notepad document, which is right here on the desktop.
You can open that up.
And then here on R1, I'm going to just go ahead and do it
manually.
So these commands here--
for brevity, I'm going to go ahead and copy/paste them in.
And I'll do that on one other device as well.
And then I'll leave you to it.
All right.
So there it is on R1.
And we'll go ahead and do R2, which are
virtually identical commands.
Only the interface numbers and quantity have changed. WEBVTT X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000
Only the interface numbers and quantity have changed.
This is a different device.
And they're both in the backbone area.
So we'll put R2 in there.
All right.
And let me just wait for one moment for that neighborship
to come up.
We'll do a show ipv6.
Actually, that's a force of habit right there.
So as I'm doing show ipv6, let's do a show ospf version
3 interface brief.
And that's going to give us a nice warm-up to some
of the commands I'm going to be sharing with you in the very
next video.
So I would encourage you to, once you
get this whole lab built--
all eight routers up and running and full adjacencies--
maybe try a ping with IPv4 or IPv6, WEBVTT X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000
maybe try a ping with IPv4 or IPv6,
all the way across the network.
Do a traceroute or two.
Have some fun.
And then leave this lab up and running.
And in the next video, what I'll do
is I'll walk you through a few of my favorite commands,
or these commands that work with OSPF
v 3, because they're slightly different.
So it's important if we're verifying or troubleshooting
a network, depending on which flavor of OSPF we've
implemented, the commands for the show commands
are slightly different.
So I'll see you in that next video,
where we'll proceed with some of those show commands.
Meanwhile, I hope this has been informative for you, WEBVTT X-TIMESTAMP-MAP=LOCAL:00:00:00.000,MPEGTS:900000
Meanwhile, I hope this has been informative for you,
and I'd like to thank you for viewing.