TS4500 Tape Library Fix List =================================================================================================== Firmware Level: TS4500_1105 Release Date: 07/24/14 =================================================================================================== - Implemented popped gripper check in calibration. - Added code for logical config reset of inventory database - Added support to get a read dump and a forced dump when drive logs are gather from the WEB UI. - Fixed problem where usernames are not logged in events when remote authentication is enabled - Fixed problem where user was not able to cancel drive service which left drives offline after a failed service attempt - Fix issue where the 3592 Wrap test wasn't returning the proper error on failure. - Fixed problem where mail notifications didn't contain the correct time - Fixed problem where web doesn't display max frame capacity correctly - Fixed problem where changing drive port speed 2 Gb/s to 4Gb/s failed resulted in the port speed being set to 1Gb/s instead of 4Gb/s - Fixed problem where Move command in Cache LCC failed with Source Element Empty. - Fixed problem where there were extraneous 0801 (failed login) events even when login is successful - Fixed problem where DSIT status for side door in a 1 frame library are incorrect - Fixed problem where invalid data was being stored in Call Home data prior to setting up Call Home - Fixed problem in cartridge stats file where data in columns was set to zero - Fixed problem where motion commands could fail due to incorrect node data - Fixed problem where the library reported calibration when drives are installed in first column of frame 1 - Fixed problem where only one Task is generated during drive code to multiple drives - Fix issue where the Primary Port on the drive was set to offline before configuring the drive, causing NDFU to failed in some cases. - Fixed problem where Frame 0 is reported for frame/Library calibration events - Fixed problem where Drive Activity VHF control wasn't set properly making the drive not send all notifications for device activity. - Fixed problem in library performance file where data in a few column were all set to zeros - Fixed problem where cleaner cartridges were not hidden from host view - Fixed problem where Volser Range Update task stopped when user tries to create more volsers than max allowed - Fix issue where drv status wasn't properly set causing WEB to show wrong drv status. - Fixed problem where drive cal errors display FCD info not FCR - Fixed problem where tasks that did not complete after a timeout where not automatically marked completed - Removed code that cleared task information during library power-on/reset - Fix issue where a failure in drive code update for FRU replacement wasn't send back to the requester. - Fixed problem where the local IP table was incorrect causing the Ethernet Rcv Message to send a dup messages. - Fixed problem where library wouldn't shuffle deep cell cartridges correctly - Fixed problem where web logs out all users right after login when the library is not configured yet - Fixed problem where user was unable to download logs when too many drive dumps are stored - Fixed problem where an empty available VEA could be wrong if sourceSTE encountered in a drive - Fixed problem where the drive URCs were incorrect for LTO drive gens - Fixed problem where LCC resets could force library into not ready state - Fix issue where lost in Ethernet connection was pointing to the incorrect location for the failure. - Fixed problem where library reported all IO cal errors as errors on the bottom IO - Fixed problem where drives coming from a different system could stay offline in the primary port (FC) - Fixed problem where the accessor could move erratically after a library POR - Fixed problem where library would inventory all drives frames after an LCC or library POR - Fixed problem where LTO5 drive WWPN is changed after Library Managed Encryption (LME) is enabled - Fixed problem where the library verify didn't test the IO station - Fixed problem where TS3500 SNMP traps where parsed with TS4500 MIB definitions - Fixed problem where drive communication issue was causing SCSI commands to failed. - Fixed problem where enabling Ipv4 DHCP disables Ipv4 port - Fixed problem where the Service user is automatically deleted from the database after Inital Setup - Fixed problem where cartridge assignments were not being limited by licensed capacity - Fixed problem where cartridge assignments via web allowed more cartridges than allocated under licensed capacity - Fixed problem where Service login after Initial Setup fails - Fixed problem where StartStEA field for shared and unassigned logical libraries was set to 0 instead of 1024 - Fixed problem where a failing task will report completed while it is still in progress - Fixed problem where task data is cleared every hour - Fixed problem where Library Verify with drive test failed and did not attempt the drive test - Fixed problem where beacon was not turning on and off correctly from web. - Fixed problem where web doesn't display max frame capacity correctly. - Fixed problem where enabling Ipv4 DHCP disables Ipv4 port . - Implemented a dialog to select a specific frame to run a Discover Hardware Action . - Fixed problem where Level of Code was truncate in the Update Firmware dialog.  - Implemented Start TLS enabled checkbox for Remote Authentication. - Added scroll bars to the web tables to have the data visible with columns of the same width - Fixed problem where carts in the exported queue were not displayed in the web with Export pending state.  - Added count information on the top right cornet of Drives page. - Fixed problem where Export data table file was not matching the Cartridge page values. - Fixed problem where Accessor was shown online when it was on Service. - Fixed problem where a Cleaning Cartridge appeared Unassigned instead of Cleaning Cartridge under Logical Library Column. - Fixed problem where cartridges incorrect Recent Usage dates appear on web. - Added support to mark multiple events as inactive at once. - Fixed problem where a Drive code update does not start after another drive code update has finished in a different Drive. - Added Web support to cancel Drive Fru Replacement. - Added Web support to track Remote Authenticated users. - Fixed problem where user was unable to uncheck heartbeat checkbox. - Fixed problem where when installing an alien .bin file, Library was not showing  error/warning message. - Fixed problem where Encryption method internal selective and barcode can not set IP values. - Added support to read the fix procedures format in Events page with Service account.